“Mini Dumper" is used for recovery of mobility such as sites, narrow streets or as a main auxiliary carrier.
In the “Mini Dumper", the dumping process is done with side covers and two damper lifting cylinders. In order to maintain the stability of the vehicle, the presser feet are operated before unloading, thus preventing sudden loads from damaging the mechanics.
The Minipacker is a rapid and economic solution in collection garbage. İt provides a modern, Clean and an innovative appearance for the environment. It has a 100% leakage-proof quality and it is much lighter than the other ones since, in this compactor there is no rear cover system present
MiniPacker can transfer Waste to other Refuse collection vehicle
This compactor can make transfer to rear loading garbage compactors.
Minipacker Leak Proof
MiniPacker garbage compactor hasn’t got rear gate. Because of this it is completely leak proof.
MiniPacker is suitable for Narrow Street
Suitable for Narrow Street.
Electric system: Control system with buttons. Electric components brands are SCHNEIDER German made, TELEMAKANIC German made and EATON English made.
Container system: The container lifts system suitable to lift containers from
120lt, 240lt, 400lt, 770lt, 1100 lt.
Paint: After coated epoxy, final color will be applied two coat that is chosen by customer.
Box
• Capacity 8 m3 excluding hopper without anyside walls or side profiles and traverces. Subframe “U” shape full length.
• Body Roof : St-52 Steel 3.0 mm Thickness
• Body Side : St-52 Steel 5.0 mm Thickness
• Body Floor : St-52 Steel 5.0 mm Thickness
Tailgate
• Compaction Ratio The compaction ratio (volumetric) varies between3:1to 5:1 – 6:1 according to the characteristic of the garbage used in thearea. Hopper Capacity (m3) The loose garbage capacity of loading
hopper is 1m3.
• Tailgate Lifting Cycle : 15 – 30 sec.
• Compaction Plate Working Cycle : 20 – 35 sec
• Steel Thickness (mm)
O Hopper Sides bottom Mild Steel 4mm
O Hopper flor extension into body Mild Steel 4mm
• Container Lifting Devices
O Suitable to lift 1.1 metal containers.
• LoadingHeight
O 1000-1200mm.(according to chassis height from ground of truck).
HydraulicSystem
• Controlled inside thecab, original P.T.O of the Truck is excluding.
• Working Pressure (bar) : 180 Bar
• Hydraulic Cylinder
O 10 units of hydraulic cylinders.
O Telescopic Cylinder with 3 stages.
O Pipesto be made of honed drawn steel pipe and cylinder miles are grinded and chrome coated agains to corrosion.
• Hydraulic Pump
O P.T.O driven Hydraulic Pump 51 cm3/rev – max.1000rpm. (depends on truck)
Operation Control
• Tailgate and ejector controls are in front of the body.
• All devices for loading control are mounted on tailgate rightside.
• System can be operated manual+Automatic.
Accessories
• Two plastic mudguards with rubber flaps at rear ends.
• 1 Rotating Beacon (gyrofare) light at top of the tailgate.
• 2 Floodlights on top of thehopper
• Two foldable type rear foot boards for crew to stand on
• Oneellipticalhandle at eachside∅ ¾ " pipe handle for the crews to grasp
• The necessary trafficlights, reflectors, and warning device sshall be mounted at rear proper to regulations
• Electrical system is separated from the circuit of the truck Specifications and dimensions are not binding.
• 8 m3 Garbage Compactor Manuel+ Automatic Control Complete:
Delivery Type
• Delivery time : in 60 days after confirm order.
• 2 pcs in 1 container 40’ OT
Box
• Capacity 10 m3 excluding hopper without anyside walls or side profiles and traverces. Subframe “U” shape full length.
• Body Roof : Steel 4.0 mm
Thickness
• Body Side : Steel 3.0 mm Thickness
• Body Floor : Steel 4.0 mm Thickness
• Side Guides : 6 mm Thickness
• Ejection Panel : ST-52 4mm
Tailgate
• Compaction Ratio The compaction ratio (volumetric) varies between3:1to 5:1 – 6:1 according to the characteristic of the garbage used in the area. Hopper Capacity (m3) The loose garbage capacity of loading hopper is 1,1 m3.
• Tailgate Lifting Cycle : 15 – 30 sec.
• Compaction Plate Working Cycle : 20 –35 sec
• Steel Thickness (mm)
O Hopper Sides bottom ST-52 Steel 4mm
O Hopper flor extension into body ST-52 Steel 4mm
O Shovel Inside : ST-52 4 mm
• Container Lifting Devices
O Suitable to lift 1.1 metal containers.
• LoadingHeight
O 1000-1200mm.(according to chassis height from ground of truck).
Hydraulic System
• Controlled inside thecab, original P.T.O of the Truck is excluding.
• Working Pressure (bar) : 180 Bar
• Hydraulic Cylinder
O 10 units of hydraulic cylinders.
O Telescopic Cylinder with 3 stages.
O Pipesto be made of honed drawn steel pipe and cylinder miles are grinded and chrome coated agains to corrosion.
O 3 mm Sewage tank fitted under tailgate.
• Hydraulic Pump
O P.T.O driven Hydraulic Piston Pump 45 cm3/rev – max.1000rpm. (depends on truck)
O PTO is not included to offer.
Operation Control
• Tailgate and ejector controls are side of the body.
• Comoaction control at rear side
• All devices for loading control are mounted on tailgate right side.
• System can be operated manual+Automatic.
Washing System
• High Pressure water pump 30-40 L/Min (150 Bar) with gun
• High Pressrue Hose Reel ½ Diameter and 15 m length
• Washing System will control at rear side.
• 250 L SS304 water tank
Accessories
• Two plastic mudguards with rubber flaps at rear ends.
• 1 Rotating Beacon (gyrofare) light at top of the tailgate.
• 2 Floodlights on top of the hopper
• Two foldable type rear foot boards for crew to stand on
• One elliptical handle at each side∅ ¾ " pipe handle for the crews to grasp
• The necessary trafficlights, reflectors, and warning device shall be mounted at rear proper to regulations
• Driver Buzzer
• Electrical system is separated from the circuit of the truck Specifications and dimensions are not binding.
Box
•Capacity 18 m3 excluding hopper without anyside walls or side profiles and traverces. Subframe “U” shape full length.
• Body Roof : St-52 Steel 3.0 mm Thickness
• Body Side : St-52 Steel 5.0 mm Thickness
• Body Floor : St-52 Steel 5.0 mm Thickness
Tailgate
• Compaction Ratio The compaction ratio (volumetric) varies between3:1to 5:1 – 6:1 according to the characteristic of the garbage used in thearea. Hopper Capacity (m3) The loose garbage capacity of loading hopper is 1,5 m3.
• Tailgate Lifting Cycle : 15 – 30 sec.
• Compaction Plate Working Cycle : 20 – 35 sec
• Steel Thickness (mm)
O Hopper Sides bottom Mild Steel 4mm
O Hopper flor extension into body Mild Steel 4mm
• Container Lifting Devices
O Suitable to lift 1.1 metal containers.
• LoadingHeight
O 1000-1200mm.(according to chassis height from ground of truck).
HydraulicSystem
• Controlled inside thecab, original P.T.O of the Truck is excluding.
• Working Pressure (bar) : 180 Bar
• Hydraulic Cylinder
O 10 units of hydraulic cylinders.
O Telescopic Cylinder with 3 stages.
O Pipesto be made of honed drawn steel pipe and cylinder miles are grinded and chrome coated agains to corrosion.
• Hydraulic Pump
O P.T.O driven Hydraulic Pump 73 cm3/rev – max.1000rpm. (depends on truck)
Operation Control
• Tailgate and ejector controls are in front of the body.
• All devices for loading control are mounted on tailgate rightside.
• System can be operated manual+Automatic.
Accessories
• Two plastic mudguards with rubber flaps at rear ends.
• 1 Rotating Beacon (gyrofare) light at top of the tailgate.
• 2 Floodlights on top of thehopper
• Two foldable type rear foot boards for crew to stand on
• Oneellipticalhandle at eachside∅ ¾ " pipe handle for the crews to grasp
• The necessary trafficlights, reflectors, and warning device sshall be mounted at rear proper to regulations
• Electrical system is separated from the circuit of the truck Specifications and dimensions are not binding.
Box
• Capacity 24 m3 excluding hopper without anyside walls or side profiles and traverces. Subframe “U” shape full length.
• Body Roof : St-52 Steel 3.0 mm Thickness
• Body Side : St-52 Steel 5.0 mm Thickness
• Body Floor : St-52 Steel 5.0 mm Thickness
Tailgate
• Compaction Ratio The compaction ratio (volumetric) varies between3:1to 5:1 – 6:1 according to the characteristic of the garbage used in thearea. Hopper Capacity (m3) The loose garbage capacity of loading hopper is 2m3.
• Tailgate Lifting Cycle : 15 – 30 sec.
• Compaction Plate Working Cycle : 20 – 35 sec
• Steel Thickness (mm)
o Hopper Sides bottom Mild Steel 4mm
o Hopper flor extension into body Mild Steel 4mm
• Container Lifting Devices
o Suitable to lift 1.1/ 2,5/ 4,5/ 7m3 metal containers.
• LoadingHeight·
o 1000-1200mm.(according to chassis height from ground of truck).
HydraulicSystem
• Controlled inside thecab, original P.T.O of the Truck is excluding.
• Working Pressure (bar) : 180 Bar
• Hydraulic Cylinder
o 10 units of hydraulic cylinders.
o Telescopic Cylinder with 3 stages.
o Pipesto be made of honed drawn steel pipe and cylinder miles are grinded and chrome coated agains to corrosion.
o The seals can durable to high temperature.
• Hydraulic Pump
o P.T.O driven Hydraulic Pump 73 cm3/rev – max.1000rpm. (depends on truck)
Operation Control
• Tailgate and ejector controls are in front of the body.
• All devices for loading control are mounted on tailgate rightside.
• System can be operated manual+Automatic.
Accessories
• Two plastic mudguards with rubber flaps at rear ends.
• 1 Rotating Beacon (gyrofare) light at top of the tailgate.
• 2 Floodlights on top of thehopper
• Two foldable type rear foot boards for crew to stand on
• Oneellipticalhandle at eachside∅ ¾" pipe handle for the crews to grasp
• The necessary trafficlights, reflectors, and warning device sshall bemounted at rear proper to regulations
• Electrical system is separatedfromthecircuit of the truckSpecifications and dimensionsare not binding.